Root cause analysis · FMCG aseptic processing

Catastrophic failure of PTFE aseptic valve bellows under hydraulic dead-head transient

A 54-head aseptic rotary can filler suffered simultaneous plastic failure of over half its valve bellows population during a routine clean-in-place cycle. Two suppliers were implicated and each had begun to construct a narrative pointing at the other. This study documents the evidence base, the causal chain, and the systemic design deficiency that made the event inevitable rather than accidental.

At a glance

The numbers that defined the event.

11.4 bar Peak hydraulic transient recorded at dead-head
2.5 bar Nominal CIP manifold operating pressure
4.6 × Exceedance over normal operating envelope
82 °C Fluid temperature — PTFE thermally softened
20,399 L/hr Peak CIP supply flow driving the closed system
54% Proportion of bellows population requiring renewal
40–50% PTFE yield strength lost at operating temperature
< 1 s Response window in which relief had to occur

All figures as recorded by calibrated instrumentation on the day of the event, or as established from published material property data for the specified polymers. No value in this study is estimated.

Section 01 · The brief

Why an independent investigation was commissioned

A high-speed aseptic can filler suffered a sudden, simultaneous failure of a substantial proportion of its valve bellows during a routine clean-in-place cycle. Two suppliers were implicated — the machine OEM and the CIP systems integrator — and each had begun to construct a narrative pointing at the other.

The client required an evidence-led determination of cause: not an opinion, and not a negotiated position between two commercially interested parties. The brief was to establish what physically happened, in what order, on the basis of instrumented data and physical evidence alone — and to produce documentation robust enough to withstand adversarial technical scrutiny.

A secondary requirement, articulated less formally but no less real, was that the findings be explicable to a non-specialist engineering management audience without diluting their technical precision. A root cause analysis that cannot be understood by the person who has to act on it has failed regardless of its accuracy.

Framing

The failure had already been characterised by both suppliers as a component quality problem. The investigation began by refusing that framing and asking a different question: what condition would have to exist for a correctly specified component to fail this way?

Section 03 · Mechanism elimination

Five competing mechanisms excluded on physical evidence.

Each candidate mechanism produces a distinct damage geometry. Elimination is performed on physical evidence before process data is consulted.

Candidate mechanism Basis for exclusion Verdict
Vacuum implosion Produces radially inward collapse. Observed geometry is radially outward expansion — the direct opposite. Load direction is unambiguous from the deformation alone. EXCLUDED
Actuator over-travel Produces axial compression damage without a radial component. All associated valves confirmed free of mechanical seizure under manual stroke test. EXCLUDED
Chemical attack PTFE presents excellent resistance across the relevant cleaning chemistry range. Chemical degradation manifests as surface crazing, mass loss or stress cracking — none present. Failure is mechanical, not chemical. EXCLUDED
Fatigue / end-of-life Fatigue propagates as crack growth and progressive breach in individual components. The observed event was simultaneous plastic deformation across a majority of the population on a five-year-old asset. Random wear cannot produce synchronised failure. EXCLUDED
Manufacturing defect A batch defect would not produce failure precisely coincident with a recorded process excursion, nor would it explain the intact PEEK collars sharing the same load path. EXCLUDED
Section 04 · Instrumented evidence

Reconstructed event sequence.

13:37
CIP cycle running. Machine HMI confirms active cleaning sequence with process fluid circulating.
13:57–13:58
Peak circuit temperature achieved across all channels: 80.7 to 82.3 °C. Thermal softening of the PTFE bellows becomes the governing material condition from this point forward.
14:12–14:24
Temperatures sustained in the 80 to 82 °C band. The softened material state persists across the whole hot rinse phase.
14:30
Peak volumetric flow of 20,398.9 L/hr. Supply pump at full output. Recovery vessel accumulating return flow throughout this period.
14:30–15:10
Forty minutes of normal high-flow, high-temperature circulation. No pressure anomaly. The system is operating exactly as designed — and filling the recovery vessel toward its limit.
15:10:13
Recovery vessel reaches capacity. High-level interlock fires and closes the return path. The drain bypass valve fails to open within the available window. The supply pump continues driving against a closed system. Hydraulic dead-head forms. Pressure spikes to 11.4 bar. Bellows yield.
15:35–15:45
Circuit temperatures fall across all channels. Active phase concluded. Damage already done.
Section 05 · Causal chain

The verified sequence, with evidence basis stated at each node.

Six-node causal chain: aseptic valve bellows failure Six sequential nodes from recovery vessel reaching capacity (01), safety interlock closing return path (02), open node where drain bypass fails to open within window (03), hydraulic dead-head forming (04), pressure transient developing to 11.4 bar (05), to thermally softened PTFE bellows yielding (06). 01 Recovery vessel reaches capacity 02 Safety interlock closes the return path 03 · Open node Drain bypass fails to open within the window 04 Hydraulic dead-head forms (20,000 L/hr) 05 Pressure transient develops (11.4 bar) 06 Thermally softened PTFE bellows yield Six-node causal chain: aseptic valve bellows failure Six sequential nodes from recovery vessel reaching capacity (01), safety interlock closing return path (02), open node where drain bypass fails to open within window (03), hydraulic dead-head forming (04), pressure transient developing to 11.4 bar (05), to thermally softened PTFE bellows yielding (06). 01 Recovery vessel reaches capacity 02 Safety interlock closes return path 03 · Open node Drain bypass fails to open in window 04 Hydraulic dead-head (20,000 L/hr) 05 Pressure transient (11.4 bar) 06 Thermally softened bellows yield
01

Recovery vessel reaches capacity

The CIP hot water recovery vessel fills to 100 per cent during the hot rinse phase. This is a normal and recurring condition, not an abnormal event — the vessel fills on a substantial proportion of cycles by design.

Evidence: process design · recorder flow integration
02

Safety interlock closes the return path

The high-level sensor activates the utility interlock, which closes the recovery vessel inlet valves to prevent overflow. This action is correct and by design. It is protective behaviour functioning exactly as intended.

Evidence: control philosophy · P&ID · supplier correspondence
03 · OPEN NODE

Drain bypass fails to open within the window

The local drain bypass valve does not open with sufficient speed to establish an alternative flow path before pressure develops. Two distinct sub-causes remain candidates: automation logic latency in the command sequence, or pneumatic exhaust restriction delaying actuator stroke under load. These are mechanistically separate and were deliberately not conflated — resolution requires controller historian timestamps comparing command issuance against confirmed position feedback.

Open node — historian data required to differentiate sub-cause
04

Hydraulic dead-head forms

The supply pump continues driving at approximately 20,000 L/hr into a system with no open outlet. The fluid column dead-heads. Kinetic energy converts to static pressure across the closed section.

Evidence: recorded flow · pump duty · first principles
05

Pressure transient develops

System pressure rises to 11.4 bar, a factor of 4.6 above the nominal manifold operating pressure. The pump has no dead-head trip and no passive relief device exists upstream of the affected components.

Evidence: calibrated recorder · timestamped 15:10:13
06

Thermally softened bellows yield

PTFE bellows operating at 80 to 82 °C, with yield strength reduced by 40 to 50 per cent against room-temperature values, are subjected to the transient. Hoop stress exceeds derated capacity. Catastrophic plastic deformation follows. Adjacent PEEK components, retaining the majority of their strength at temperature, survive intact.

Evidence: specimen morphology · material property data · recorded temperature
Section 07 · Systemic determination

The proximate cause is a valve that did not open in time. The underlying condition is a relief path with no redundancy, protecting a derated material, against a trigger that recurs by design. Addressing the first restores production. Only addressing the second removes the failure.

Section 08 · Corrective action framework

Tiered by intervention type, not by convenience.

Tier 1

Containment

Before return to service
  • Full inspection of the affected component population — not only the units that visibly failed, since partial plastic strain may not be apparent on visual examination.
  • Physical inspection of the bypass valve actuator and solenoid exhaust path for residue accumulation or restriction, with findings formally recorded.
  • Suspension of automatic recovery vessel management until relief response is verified adequate or an interim procedural control is established.
Tier 2

Correction

Removes the proximate cause
  • Revision of the control sequence so that the bypass valve is commanded open before, not after, the return path interlock closes. The relief route must be established prior to the closure that necessitates it.
  • Timed auto-cycle stroke verification of the bypass valve under operating conditions, benchmarked against interlock response speed, with the result documented as a commissioning record.
  • Inclusion of solenoid exhaust path inspection in the planned maintenance schedule at a frequency reflecting the cleaning chemistry exposure.
Tier 3

Engineering change

Removes the systemic vulnerability
  • Installation of a passive pressure relief device upstream of the thermoplastic components, set below their derated capacity at maximum process temperature. Passive relief is independent of control logic, actuation timing, and pneumatic supply integrity.
  • Configuration of a supply pump dead-head trip on the pressure-rise-at-zero-flow signature, removing the energy source rather than only providing an escape route for it.
  • Formal review of pressure protection philosophy across all circuits containing thermoplastic sealing elements exposed to elevated-temperature cleaning cycles.
Section 09 · Method notes

Three observations transferable to subsequent forensic work.

01

Read the specimen before reading the data.

Physical morphology is the least corruptible evidence available and it is destroyed by handling, cleaning and replacement activity. Establishing the load direction and mechanism from the component itself, before consulting process data, guards against the confirmation bias that follows from knowing what the data says first.

02

Suppliers write your case for you.

In correspondence composed to deflect responsibility, technically competent parties routinely state the design intent of their own equipment in unambiguous terms. A supplier explaining what their valve should do, in the course of arguing that the fault lies elsewhere, has documented the standard against which their equipment is subsequently measured. Their own written words carry evidential weight that no third-party assertion matches.

03

Distinguish the cause from the condition, and say so plainly.

The proximate cause answers the question the client asked. The underlying condition answers the question they will ask after the next failure. A report that delivers only the first is technically correct and practically worthless within eighteen months.

Client, supplier and asset identities have been redacted throughout. All process data, failure morphology, engineering reasoning and conclusions are reproduced unaltered from the original investigation.

This document is prepared as a technical portfolio record. It does not constitute legal advice. Liability determinations in the original investigation remained subject to outstanding data retrieval and legal review at the point of issue.

← All case studies
Start a conversation

Bring the failure that won't stay fixed.

Interim, contract and project engagements across the UK.